Our customers use our products in a wide variety of combinations and situations on a daily basis to solve their problems. Here are some examples which may give you some ideas for your own setup.
If you have a photo or video that shows a solution to a problem, or if you just want to show off your install. Send a copy of the photo or video along with an explanation to paul@pinellaspowerproducts.com.
This gallery is divided into three sections for your convenience.
Section 1: Miscellaneous Videos.
Section 2: EV6010 Tech support Videos.
Section 3: Miscellaneous Photos.
Miscellaneous Videos
- Quiet Box for Honda EU2000i sold only in Japan.発電機
- 2010 Fuel Injected EU6500is not sold in U.S.A. watch video at 2:30 you can see the throttle body clearly
- Demo of the first Electric start Honda EU2000i
- Part 1 of How I built the Electric start Honda EU2000i
- Part 2 of how I built the Electric start Honda EU2000i
- This unit was Built by Pinellas Power Products For the Alaska Center for Energy and Power, At University of Alaska Fairbanks
- Janina makes home back up power sound simple
- How The EU7000iS Fuel Injection system works part 1
- How The EU7000iS Fuel Injection system works part 2
- Welcome to my world, trying to explain back up power in 102 degree heat
EV6010 Tech Support Videos
If you feel you have received valuable information or advice and would like to make a donation toward (phone, tech support, and video tech support) please leave a tip.
Engine Assembly
- 2 EV6010 Video Cylinder Head Inspection part 1 Valve stem to valve guide clearance
- 3 EV6010 Video Cylinder Head Inspection part 2 Checking for warpage
- 4 EV6010 Video Cylinder Head Assembly cut valve seats and install valves
- 5 EV6010 Video Cylinder Head Assembly finish installing the valves
- 6 EV6010 Video Cylinder Head Assembly installation of rocker arms and camshaft
- 7 EV6010 Video Cylinder Head Assembly thermostat case and adjust valves
- 8 EV6010 Video Cylinder Head Assembly finish adjusting valve clearance
- 9 EV6010 Video Block Inspection checking for warpage and measuring cylinder bores
- 10 EV6010 Video Bore Chamfer and hone cylinders to fit over-sized pistons
- 11 EV6010 Video Recheck cylinder bores and fit main bearings to correct clerance
- 12 EV6010 Video Check main bearings with plastigage to confirm correct clearance
- 13 EV6010 Video Install balancer bearings and install rods to pistons
- 14 EV6010 Video Install pistons and rings into block and start on rod bearings
- 15 EV6010 Video Fit rod bearings and check with plastigage to confirm clearance
- 16 EV6010 Video Install oil pick up and pressure regulator and rod caps then torque
- 17 EV6010 Video Install main seals and bolt case halves together then torque
- 18 EV6010 Video Install oil joint tube, oil reservoir and balancer shaft
- 19 EV6010 Video Install governor assembly and governor cover with new bearing
- 20 EV6010 Video Torque governor cover and install breather assembly
- 21 EV6010 Video Inspect and install oil pump drive gear, oil pump and cover
- 22 EV6010 Video Install oil restrictor jet and cylinder head then torque
- 23 EV6010 Video Install water bypass hose, intake adapter and valve cover
- 24 EV6010 Video Install oil pressure switch, oil filter and give dowel pin explanation
Engine Install
- 27 EV6010 Video Install coil mount, starter motor, wire harness, heat shield and exhaust
- 28 EV6010 Video Install intake manifold, flywheel and exhaust cover
- 29 EV6010 Video Install engine mounts, governor arm and bell housing
- 30 EV6010 Video Install rubber engine mounts and assemble carburetor
- 31 EV6010 Video Install carburetor assembly and choke actuator bracket
- 32 EV6010 Video Install choke actuator, choke linkage, throttle linkage and fan shroud
- 33 EV6010 Video Install radiator mount brackets, radiator and radiator hoses
- 34 EV6010 Video Install sound proof cover, fuel pump mount and purge tank with bracket
- 35 EV6010 Video Install fuel pump and ignition coil and fill with coolant
- 36 EV6010 Video Install spark plugs, fuel pipe & filter and plastic cover
Stator Install
- 37 EV6010 Video Explanation of how to remove stator assembly
- 38 EV6010 Video Explanation of oil pump leaks and installation of bell housing
- 39 EV6010 Video Install stator, rotor, cover and fan into rear housing
- 40 EV6010 Video Install stator and rotor sub assembly and generator mounts
- 41 EV6010 Video Install brushes, voltage regulator and rectifier diode
- 42 EV6010 Video Install cooling fan relay, circuit beakers and output harness
- 43 EV6010 Video Finish output harness Install control box and explain 12V charging system
- 44 EV6010 Video Install airbox and add oil to engine
- 45 EV6010 Video Install generator onto test stand and get ready testing
Start Up
- 46 EV6010 Video Start Up and test run of rebuilt generator 1
- 47 EV6010 Video Start Up and test run of rebuilt generator 2
Troubleshooting and Repair
- 48 EV6010 Video How to easily change the Starter Motor on an EV6010
- 49 EV6010 Video Cooling System description and function
- 50 EV6010 Simple carburetor clean out